TEL: +86-158-5877-7327
A bimetal cable lug is a normal selection direction when an aluminum conductor must terminate on a copper busbar or copper equipment pad. The cable end needs a connection intended for aluminum, while the bolted contact needs a copper-compatible interface. Confirm both sides before choosing the lug size.
That does not mean every aluminum cable needs a bimetal termination. An all-aluminum connection or an equipment-approved, dual-rated connector may require a different arrangement. Start with the cable datasheet and equipment terminal drawing, then check the proposed connector’s documented application.
A conventional compression-type bimetal lug combines an aluminum barrel with a copper contact section. Designs differ: some have a copper palm, while others use a defined copper contact insert. The manufacturer’s drawing must show how the intended contact is made.
CONWELL’s bimetal cable lug range is intended for aluminum-cable-to-copper-terminal transitions. Use the category to identify candidates, then confirm the exact design against the project rather than treating every item in the range as interchangeable.

Bimetal lug example from CONWELL’s official website. Verify the contact arrangement and dimensions on the proposed model’s drawing.
The practical concern is an uncontrolled aluminum-to-copper field joint. Moisture at a dissimilar-metal interface can promote galvanic corrosion, while surface oxides and an unsuitable connection process can impair electrical contact. A designed transition helps manage the interface; it does not remove the need for correct installation and environmental protection.
| Connection | Selection direction | Condition to confirm |
|---|---|---|
| Aluminum cable to copper busbar or pad | Consider a purpose-designed Al/Cu bimetal lug. | Approved conductor construction, copper contact arrangement, dimensions, and installation method. |
| Aluminum cable to aluminum terminal | An aluminum lug may be appropriate. | Equipment approval and compatibility with the specific conductor and contact surface. |
| Copper cable to copper terminal | Use a suitable copper-conductor termination. | Conductor class, terminal geometry, and specified installation process. |
| Equipment already has an approved dual-rated connector | Review the equipment’s specified connection system first. | Accepted conductor, rating, mounting interface, and complete installation instructions. |
A silver finish does not tell the buyer whether a lug is aluminum, plated copper, or a purpose-designed transition product. Likewise, a plated aluminum palm is not automatic evidence that the assembly is approved for a copper busbar.
Where both interfaces are aluminum, review the available aluminum cable lugs against the equipment requirements. Where the equipment pad is copper, request explicit confirmation of the transition arrangement instead of substituting an ordinary aluminum lug.

DL aluminum lug shown for comparison. Its appearance alone does not establish approval for a copper contact surface.
Do not add a loose washer, change the contact compound, or modify the palm to create an improvised transition. An alternative arrangement needs approval for the complete connection, including materials, contact faces, hardware, and installation conditions.
Record the aluminum conductor’s nominal cross-section, actual diameter, stranding class, and shape. Round, compacted, and sector-shaped conductors of the same nominal area can require different treatment. Ask whether shaping or pre-rounding is required for the proposed lug; do not remove strands or use an oversized barrel as a workaround.
Check hole diameter, hole count and pitch, contact-face dimensions, palm thickness, and overall length. Confirm that the lug seats as designed without interference from adjacent phases, barriers, covers, or the cable bend. Use the equipment drawing’s specified hole clearance, not the bolt designation alone.
For the broader dimensional review, see the cable lug size and terminal-interface guide. Material compatibility must be resolved before dimensional fit can complete the selection.
CONWELL describes its DTL-2 series as an aluminum-conductor-to-copper-terminal transition option. Its copper-aluminum transition lug details provide a starting point for model review. Request the exact size suffix and current drawing; a family name does not establish every size’s hole or barrel dimensions.
For a compression lug, obtain the approved tool and die assignment, crimp profile, number and positions of compressions, strip length, and insertion requirements. A die marked with the same nominal cable size is not enough to prove compatibility. Follow the specified conductor preparation and contact-compound instructions rather than borrowing a procedure from another connector.
Treat barrel compression and busbar bolting as separate operations. Confirm the equipment-approved fastener arrangement and tightening instructions. There is no universal torque value for every lug, bolt, and busbar combination. Installation should be performed by qualified personnel on isolated equipment under the site’s safety procedures.
Request the evidence relevant to the purchase: a controlled drawing, material and interface description, installation instructions, traceable product identification, and applicable electrical and mechanical test reports. Check that reports cover the proposed design, conductor, and installation system. A company quality certificate does not establish the performance of that specific combination.
Can a copper-palm bimetal lug be used in reverse, on copper cable and an aluminum busbar?
Do not assume so. The barrel and contact section have different intended interfaces. That reverse connection needs a separately approved connector or transition arrangement.
Does a bimetal lug eliminate all corrosion risk?
No. It provides a designed metal transition, but exposed contacts, damaged finishes, moisture, and unsuitable hardware still require assessment. Specify environmental protection for the installed connection.
Can an approved mechanical lug replace a compression bimetal lug?
Possibly, if the equipment and project accept it for the exact conductor and contact interface. Verify its rating and installation requirements; material compatibility alone does not authorize a change of termination method.
Is a photograph enough to request a replacement?
No. Add the cable datasheet, equipment terminal drawing, dimensions, and existing identification where available. A photograph can explain the arrangement but cannot establish hidden materials or conductor compatibility.
To request a bimetal cable lug proposal, prepare:
Send CONWELL your cable data and equipment terminal drawing and request a model-specific compatibility review and quotation. Ask the supplier to confirm the two metal interfaces, dimensional fit, installation method, and supporting documents in the response.
Written by the CONWELL international trade team, led by Matt, General Manager, who brings more than 20 years of international trade experience and deep expertise in the power fittings industry. He also leads CONWELL's CNAS laboratory, overseeing product testing, quality control, and technical compliance.
TEL: +86-158-5877-7327
No. 16, Waixi Road, Lingang Economic Development Zone, Yueqing Bay Port Area, Yueqing City, Wenzhou City, Zhejiang Province, China
COPYRIGHT © 2025 ZHEJIANG KEYI ELECTRIC GROUP CO., LTD. ALL RIGHTS RESERVED.
We value your privacy
We use cookies to enhance your browsing experience, serve personalised ads or content, and analyse our traffic. By clicking "Accept All", you consent to our use of cookies.
Customise Consent Preferences
We use cookies to help you navigate efficiently and perform certain functions. You will find detailed information about all cookies under each consent category below.
The cookies that are categorised as "Necessary" are stored on your browser as they are essential for enabling the basic functionalities of the site. Show more
Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.
Functional cookies help perform certain functionalities like sharing the content of the website on social media platforms, collecting feedback, and other third-party features.
Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics such as the number of visitors, bounce rate, traffic source, etc.
Performance cookies are used to understand and analyse the key performance indexes of the website which helps in delivering a better user experience for the visitors.
Advertisement cookies are used to provide visitors with customised advertisements based on the pages you visited previously and to analyse the effectiveness of the ad campaigns.